1946伟德国际

<address id="bhrjl"><listing id="bhrjl"><meter id="bhrjl"></meter></listing></address><noframes id="bhrjl">
<noframes id="bhrjl"><form id="bhrjl"></form>
    <form id="bhrjl"><nobr id="bhrjl"><meter id="bhrjl"></meter></nobr></form>

    <address id="bhrjl"><dfn id="bhrjl"><menuitem id="bhrjl"></menuitem></dfn></address>

    <form id="bhrjl"></form>
    <noframes id="bhrjl"><address id="bhrjl"><nobr id="bhrjl"></nobr></address>
      <noframes id="bhrjl">

        <address id="bhrjl"></address>
        <noframes id="bhrjl">
        <form id="bhrjl"></form>

          • Login
          • Register
          • 800-HPALLOY
          • 1985 E 500 N Windfall, IN 46076
            444 Wilson St Tipton, IN 46072
            Post Office Box 40 Tipton, IN 46072
            tel:8004725569

          Inconel 718
          AMS 5596 AMS 5662 ASTM B637
          UNS N07718 High Temperature (UNS N07718)

          Request a quote

          Ni 52.5, Cr 19.0 Fe 18.5 Mo 3.0 Nb+Ta 3.6

          High Performance Alloys stocks and produces Inconel 718 in this grade in the following forms: Bar, flat bar, wire cuts, loose coil, wire reel, sheet, plate, tube, fitting, disk, machined. Request quote on this grade.

           

          Download PDF - Or view as HTML

           

          Overview

          Inconel 718 is a Gamma Prime strengthened alloy with excellent mechanical properties at elevated temperatures, as well as cryogenic temperatures. Suitable for temperatures upto around 1300 F. Can be readily worked and age hardened.

          Excellent strength from -423 degrees F to 1300 degrees F (-253 degrees C to 705 degrees C). Age hardenable and may be welded in fully aged condition, Excellent oxidation resistance up to 1800 degrees F (980 degrees C). Typically sold in the solution annealed temper, but can be ordered aged, cold worked, or cold worked & aged.


          Applications

          Uses for Inconel 718 tend to be in the field of gas turbine components and cryogenic storage tanks. Jet engines, pump bodies and parts, rocket motors and thrust reversers, nuclear fuel element spacers, hot extrusion tooling. Other popular uses are high strength bolting, and down hole shafting.

          Chemistry

          Chemical Requirements

          Ni

          Fe

          Mo

          Mn

          Si

          Cr

          C

          Max

          55.0

          Bal

          3.30

          0.35

          0.35

          21.0

          0.08

          Min

          50.0

          2.80

          17.0


           

          Tensile Data

          Mechanical Property Requirements

          Ultimate Tensile

          Yield Strength (0.2% OS)

          Elong. in 2 in. (50mm) or 4D min, %

          R/A

          Hardness Brinell

          Min

          185 KSi

          150 KSi

          12

          15

          331

          Max

          Min

          1275 MPa

          1034 MPa

          Max


          Specifications

          Form

          Standard

          Metal Type

          UNS N07718

          Bar

          ASTM B637 AMS 5662 AMS 5663 AMS 5664 PWA 1009 PWA 1010 GE B50TF15

          Wire

          AMS 5832

          Sheet

          ASTM B670 AMS 5596 AMS 5597 PWA 1033 GE B50TF14 ASTM B670 ASTM B637

          Plate

          ASTM B670 AMS 5596 AMS 5597 PWA 1033 GE B50TF15 ASTM B670 ASTM B637

          Tube
          AMS 5589 AMS 5590
          Pipe
          AMS 5589 AMS 5590

          Fitting

           

          Forging

          ASTM B637 AMS 5562 AMS 5663 AMS 5664 PWA 1009 PWA 1010 GE B50TF15

          Weld Wire

          A5.14 ERNiFeCr-2

          Weld Electrode
           

          Din

          2.4668


           

          Machining

          Machinability Ratings

          Nickel & cobalt base corrosion, temperature and wear-resistant alloys, such as Inconel 718, are classified as moderate to difficult when machining, however, it should be emphasized that these alloys can be machined using conventional production methods at satisfactory rates. During machining these alloys work harden rapidly, generate high heat during cutting, weld to the cutting tool surface and offer high resistance to metal removal because of their high shear strengths. The following are key points which should be considered during machining operations:

          CAPACITY - Machine should be rigid and overpowered as much as possible.
          RIGIDITY - Work piece and tool should be held rigid. Minimize tool overhang.
          TOOL SHARPNESS - Make sure tools are sharp at all times. Change to sharpened tools at regular intervals rather than out of necessity. A 0.015 inch wear land is considered a dull tool.
          TOOLS - Use positive rake angle tools for most machining operations. Negative rake angle tools can be considered for intermittent cuts and heavy stock removal. Carbide-tipped tools are suggested for most applications. High speed tools can be used, with lower production rates, and are often recommended for intermittent cuts.
          POSITIVE CUTS - Use heavy, constant, feeds to maintain positive cutting action. If feed slows and the tool dwells in the cut, work hardening occurs, tool life deteriorates and close tolerances are impossible.
          LUBRICATION - lubricants are desirable, soluble oils are recommended especially when using carbide tooling. Detailed machining parameters are presented Tables 16 and17. General plasma cutting recommendations are presented in Table 18.

           

          Table 16
          RECOMMENDED TOOL TYPES AND MACHINING CONDITIONS
          Operations Carbide Tools
          Roughing, with severe interruption Turning or Facing C-2 and C-3 grade: Negative rake square insert, 45 degree SCEA1, 1/32 in. nose radius. Tool holder: 5 degree neg. back rake, 5 degree neg. side rake. Speed: 30-50 sfm, 0.004-0.008 in. feed, 0.150 in depth of cut. Dry2, oil3, or water-base coolant4.
          Normal roughing Turning or Facing C-2 or C-3 grade: Negative rate square insert, 45 degree SCEA, 1/32 in nose radius. Tool holder: 5 degree neg. back rake, 5 degree neg. side rake. Speed: 90 sfm depending on rigidity of set up, 0.010 in. feed, 0.150 in. depth of cut. Dry, oil, or water-base coolant.
          Finishing Turning or Facing C-2 or C-3 grade: Positive rake square insert, if possible, 45 degree SCEA, 1/32 in. nose radius. Tool holder: 5 degree pos. back rake, 5 degree pos. side rake. Speed: 95-110 sfm, 0.005-0.007 in. feed, 0.040 in. depth of cut. Dry or water-base coolant.
          Rough Boring C-2 or C-3 grade: If insert type boring bar, use standard positive rake tools with largest possible SCEA and 1/16 in. nose radius. If brazed tool bar, grind 0 degree back rake, 10 degree pos. side rake, 1/32 in. nose radius and largest possible SCEA. Speed: 70 sfm depending on the rigidity of setup, 0.005-0.008 in. feed, 1/8 in. depth of cut. Dry, oil or water-base coolant.
          Finish Boring C-2 or C-3 grade: Use standard positive rake tools on insert type bars. Grind brazed tools as for finish turning and facing except back rake may be best at 0 degrees. Speed: 95-110 sfm, 0.002-0.004 in feed. Water-base coolant.
          Notes:
          1 SCEA - Side cutting edge angle or lead angle of the tool.

          2 At any point where dry cutting is recommended, an air jet directed on the tool may provide substantial tool life increases. A water-base coolant mist may also be effective.

          3 Oil coolant should be premium quality, sulfochlorinated oil with extreme pressure additives. A viscosity at 100 degrees F from 50 to 125 SSU.

          4 Water-base coolant should be premium quality, sulfochlorinated water soluble oil or chemical emulsion with extreme pressure additives. Dilute with water to make 15:1 mix. Water-base coolant may cause chipping and rapid failure of carbide tools in interrupted cuts.

           

          Table 17
          RECOMMENDED TOOL TYPES AND MACHINING CONDITIONS
          Operations Carbide Tools
          Facing Milling Carbide not generally successful, C- grade may work. Use positive axial and radial rake, 45 degree corner angle, 10 degree relief angle. Speed: 50-60 sfm. Feed: 0.005-0.008 in. Oil or waterbase coolants will reduce thermal shock damage of carbide cutter teeth.
          End Milling Not recommended , but C-2 grades may be successful on good setups. Use positive rake. Speed: 50-60 sfm. Feed: Same as high speed steel. Oil or water-base coolants will reduce thermal shock damage.
          Drilling C-2 grade not recommended, but tipped drills may be successful on rigid setup if no great depth. The web must thinned to reduce thrust. Use 135 degree included angle on point. Gun drill can be used. Speed: 50 sfm. Oil or water-base coolant. Coolant-feed carbide tipped drills may be economical in some setups.
          Reaming C-2 or C-3 grade: Tipped reamers recommended, solid carbide reamers require vary good setup. Tool geometry same as high speed steel. Speed: 50 sfm. Feed: Same as high speed steel.
          Tapping Not recommended, machine threads, or roll-form them.
          Electrical Discharge Machining The alloys can be easily cut using any conventional electrical discharge machining system (EDM) or wire (EDM).
          Notes:
          5 M-40 series High Speed Steels include M-41 , M-42, M-43, M-44, M-45 and M-46 at the time of writing. Others may be added and should be equally suitable.

          6 Oil coolant should be a premium quality, sulfochlorinated oil with extreme pressure additives. A viscosity at 100 degree F from 50 to 125 SSU.

          7 Water-base coolant should be premium quality, sulfochlorinated water soluble oil or chemical emulsion with extreme pressure additives. Dilute with water to make 15:1 mix.

           

          Table 18
          Plasma Arc Cutting
          Inconel 718 can be cut using any conventional plasma arc cutting system. The best arc quality is achieved using a mixture of argon and hydrogen gases. Nitrogen gas can be substituted for hydrogen gases, but the cut quality will deteriorate slightly. Shop air or any oxygen bearing gases should be avoided when plasma cutting these alloys.

           

          INCONEL® is a registered trademark of the INCO family of companies.



          <address id="bhrjl"><listing id="bhrjl"><meter id="bhrjl"></meter></listing></address><noframes id="bhrjl">
          <noframes id="bhrjl"><form id="bhrjl"></form>
            <form id="bhrjl"><nobr id="bhrjl"><meter id="bhrjl"></meter></nobr></form>

            <address id="bhrjl"><dfn id="bhrjl"><menuitem id="bhrjl"></menuitem></dfn></address>

            <form id="bhrjl"></form>
            <noframes id="bhrjl"><address id="bhrjl"><nobr id="bhrjl"></nobr></address>
              <noframes id="bhrjl">

                <address id="bhrjl"></address>
                <noframes id="bhrjl">
                <form id="bhrjl"></form>

                  aviation

                  Mobile phone

                  news

                  constellation

                  news

                  mailbox

                  culture

                  Blog

                  education